40.5kV Manual Operation Mechanism for Spring-Loaded Inlet of SF6 Gas-Insulated Switchgear
Key attributes
| Brand | Switchgear parts |
| Model NO. | 40.5kV Manual Operation Mechanism for Spring-Loaded Inlet of SF6 Gas-Insulated Switchgear |
| Rated voltage | 40.5kV |
| Rated normal current | 630A |
| Rated frequency | 50/60Hz |
| Series | RNC-40.5 |
Product descriptions from the supplier
This series of mechanisms adopts flat spiral spring energy storage to control the action of the load switch, and the grounding operation adopts compression spring energy storage control. There are three operating stations for closing, opening, and grounding in the work position. This series of products has five interlocking functions, small size, easy installation, and strong adaptability. This product has passed the full inspection and is in compliance with the relevant requirements of G8 3804-2004 "3.6kV-40.5kV High Voltage AC Load Switches", GB 3906-2006 "3.6-40.5kV AC Metal Enclosed Switchgear and Control Equipment", and GB16926-2009 "High Voltage AC Load Switchgear Fuse Combination Electrical Appliances".Suitable for 33-40.5kV SF6 gas filling cabinet
Operatinginstructions for spring mechanism
Closing operation
Make sure to check the products without transportation will be fixed on thedeformation mechanism of load switch, the use of the operating handle is insertedinto the upper part of special institutions, clockwise rotation about 90 degrees, theload in the body underthe action ofthe spring force main loop switch. Or the electricoperation, press the closing button, the motor drives the mechanism to completethe switch on and turn operation, at this time can not carry on the ground operation.
Switching operation
The operating handle is inserted into the upper part of the mechanism and rotatescounterclockwise about 90 degrees, and the load switch is operated under theaction of the force ofthe mechanism spring, and the main circuit is split. Or electricoperation, according to the switch button, the motor drives the mechanism tocomplete the switching operation, at this time, it can do the closing operation or thegrounding operation.
Earthing closing and earthing switching operation
The operating handle is inserted into the lower part of the mechanism and rotatesabout 90 degrees clockwise. The load switch is closed to the ground circuit underthe action of the force of the mechanism spring, so that the main circuit closingoperation can not be performed at this time.The operating handle rotates about 90 degrees counterclockwise, and the loadswitch switches the grounding circuit under the action of the force of the mechanismspring, which can be used for closing operation or grounding operation.
Modelcomposition and meaning
Appearance and installation dimensions
Related Products
-
RNV-B1-12 GIS Sf6 Break Switch Circuit Breaker for Gas Insulated Switchgear
-
RNN-12 630A SF6 Gas Insulated Load Isolation Switch
-
RNN-12 SF6 Gas Insulated Load Isolation Switch (with Grounding)
-
RNV-A1-12D-1250A SF6 High Voltage Gas Insulated Inflatable Cabinet Circuit Breaker
-
24kV GIS Sf6 Break Switch Circuit Breaker for Gas Insulated Switchgear
-
24kV SF6 gas insulated load isolation switch (three position with isolation)
-
12KV SF6 filling cabinet gas insulated electric incoming spring operating mechanism
Related Knowledges
-
Faults and Handling of Single-phase Grounding in 10kV Distribution LinesCharacteristics and Detection Devices for Single-Phase Ground Faults1. Characteristics of Single-Phase Ground FaultsCentral Alarm Signals:The warning bell rings, and the indicator lamp labeled “Ground Fault on [X] kV Bus Section [Y]” illuminates. In systems with a Petersen coil (arc suppression coil) grounding the neutral point, the “Petersen Coil Operated” indicator also lights up.Insulation Monitoring Voltmeter Indications:The voltage of the faulted phase decreases (in01/30/2026 -
Neutral point grounding operation mode for 110kV～220kV power grid transformersThe arrangement of neutral point grounding operation modes for 110kV～220kV power grid transformers shall meet the insulation withstand requirements of transformer neutral points, and shall also strive to keep the zero-sequence impedance of substations basically unchanged, while ensuring that the zero-sequence comprehensive impedance at any short-circuit point in the system does not exceed three times the positive-sequence comprehensive impedance.For 220kV and 110kV transformers in new constructi01/29/2026 -
Why Do Substations Use Stones, Gravel, Pebbles, and Crushed Rock?Why Do Substations Use Stones, Gravel, Pebbles, and Crushed Rock?In substations, equipment such as power and distribution transformers, transmission lines, voltage transformers, current transformers, and disconnect switches all require grounding. Beyond grounding, we will now explore in depth why gravel and crushed stone are commonly used in substations. Though they appear ordinary, these stones play a critical safety and functional role.In substation grounding design—especially when multiple gr01/29/2026 -
Why Must a Transformer Core Be Grounded at Only One Point? Isn't Multi-Point Grounding More Reliable?Why Does the Transformer Core Need to Be Grounded?During operation, the transformer core, along with the metal structures, parts, and components that fix the core and windings, are all situated in a strong electric field. Under the influence of this electric field, they acquire a relatively high potential with respect to ground. If the core is not grounded, a potential difference will exist between the core and the grounded clamping structures and tank, which may lead to intermittent discharge.I01/29/2026 -
Understanding Transformer Neutral GroundingI. What is a Neutral Point?In transformers and generators, the neutral point is a specific point in the winding where the absolute voltage between this point and each external terminal is equal. In the diagram below, pointOrepresents the neutral point.II. Why Does the Neutral Point Need Grounding?The electrical connection method between the neutral point and earth in a three-phase AC power system is called theneutral grounding method. This grounding method directly affects:The safety, reliabilit01/29/2026 -
What’s the Difference Between Rectifier Transformers and Power Transformers?What is a Rectifier Transformer?"Power conversion" is a general term encompassing rectification, inversion, and frequency conversion, with rectification being the most widely used among them. Rectifier equipment converts input AC power into DC output through rectification and filtering. A rectifier transformer serves as the power supply transformer for such rectifier equipment. In industrial applications, most DC power supplies are obtained by combining a rectifier transformer with rectifier equ01/29/2026
