Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

Coil Span Factor (Pitch Factor) Definition and CharacteristicsDefinition of Pitch Factor (Kₙ)The coil span factor (also known as the chording factor) Kₙ is defined as the ratio of the induced voltage in a short-pitched coil to that in a full-pitched coil. The distance between the two sides of a coil is termed thecoil span, which is characterized by its electrical angle to indicate the degree of short-pitching.Physical Meaning of Pole PitchThe angular distance between the central lines of adjacen

Synchronous Reactance and Impedance PrinciplesSynchronous reactance (Xₛ) is an imaginary reactance used to represent voltage effects in the armature circuit, arising from both the actual armature leakage reactance and air gap flux variations due to armature reaction. Similarly, synchronous impedance (Zₛ) is a fictitious impedance that accounts for voltage effects from the armature resistance, leakage reactance, and air gap flux changes caused by armature reaction.The actual generated voltage com

The Constant Flux Linkage Principle in Alternator TransientsThe constant flux linkage concept is fundamental to analyzing alternator transients. It states:In a closed circuit with zero resistance and capacitance, flux linkages remain unchanged following a sudden disturbance, preserving their pre-disturbance values.In alternators, armature and field windings exhibit negligible capacitance, and their resistances are insignificant compared to inductances. Thus, these windings can be treated as pure

Resistance SwitchingResistance switching refers to the practice of connecting a fixed resistor in parallel with the contact gap or arc of a circuit breaker. This technique is applied in circuit breakers with high post-arc resistance in the contact space, primarily to mitigate re-striking voltages and transient voltage surges.Severe voltage fluctuations in power systems arise from two main scenarios: interrupting low-magnitude inductive currents and breaking capacitive currents. Such overvoltages

Definition: Insulation coordination refers to the process of determining the insulation levels of power system components. In essence, it is about establishing the insulation strength of equipment. The internal and external insulation of electrical equipment is subjected to both continuous normal voltage and temporary abnormal voltage.Equipment insulation is engineered to withstand the highest power - frequency system voltage, occasional temporary power - frequency overvoltages, and occasional l

Definition: A sag template is a tool used to accurately determine the positioning and height of supports on a profile. It defines the limits for vertical and wind loads, and also establishes minimum clearance angles between the sag and the ground for safety. Typically crafted from transparent materials such as celluloid or plexiglass (and occasionally cardboard), the sag template features the following marked curves: Hot Template Curve (Hot Curve) Ground Clearance Curve Support Foot or Tower Cur

Definition: The phase of an alternating quantity represents the proportion of a complete cycle that the quantity has traversed relative to a designated reference origin. In the context of alternating electrical or physical phenomena, when two such quantities share identical frequencies, and their respective maxima (peaks) and minima (troughs) coincide precisely in time, these quantities are characterized as beingin phase. This synchronization indicates a perfect temporal alignment, where the wav

The Biot-Savart Law is employed to determine the magnetic field intensity dHnear a current-carrying conductor. In other words, it describes the relationship between the magnetic field intensity generated by a source current element. This law was formulated in 1820 by Jean-Baptiste Biot and Félix Savart. For a straight wire, the direction of the magnetic field adheres to the right-hand rule. The Biot-Savart Law is also referred to as Laplace’s law or Ampère&rsq

Definition: Voltage regulation (or line regulation) refers to the variation in voltage at the receiving end of a transmission line when the full load at a specified power factor is removed, with the sending-end voltage maintained constant. In simpler terms, it is thepercentage changein the load-end voltage when transitioning from no-load to full-load conditions. This parameter is expressed as a fraction or percentage of the receiving-end voltage, serving as a critical metric for assessing the st

Factors in Contactor Contact DesignThe following factors are considered when designing contactor contacts:Current-Carrying CapacityThe current-carrying capacity of contacts is a primary consideration in design, directly influencing material selection. Hard-drawn copper or forged copper are preferred choices to ensure optimal performance.Contact PressureContact pressure is directly proportional to current-carrying capacity—an increase in pressure enhances the contact's ability to carry