Free Expert Guides on Power Systems, Circuit Design & Electrical Troubleshooting

What is a Centrifugal Switch?Centrifugal Switch DefinitionA centrifugal switch is an electrical component that activates based on the centrifugal force generated by a motor’s rotating shaft to control motor start-up.Operational MechanismA single-phase AC engine has a centrifugal switch inside its case, which is attached to the engine shaft. When the engine is off and motionless, the switch is closed.When the engine is switched on, the switch drives electricity to the capacitor and the extra coil

What is a ADC ?Analog to Digital Converter DefinitionAn Analog to Digital Converter (ADC) is a device that changes a continuous analog signal into a discrete digital signal.ADC Process Sampling and Holding Quantizing and EncodingSampling and HoldingIn Sampling and Holding (S/H), the continuous signal is sampled and held steady for a short period. This removes variations in the input signal that could affect conversion accuracy. The minimum sampling rate must be twice the maximum frequency of the

What is a DAC?Overview of Digital-to-Analog ConvertersDigital-to-Analog Converter (DAC), also known as D/A converter, is abbreviated as DAC. It is a device that converts digital quantities into analog ones. DAC is essentially composed of four parts: weighted resistor network, operational amplifier, reference power supply, and analog switch.Working PrincipleThe DAC is mainly composed of digital registers, analog electronic switches, weighted-resistor networks, power amplifiers, and reference volt

The development direction of charging pileAs an important supporting facility for new energy vehicles, the development direction of charging piles is directly related to the future development of the new energy automobile industry. According to the latest search results, the development direction of charging piles mainly includes the following aspects:High power fast charge technologyIn order to meet the needs of the market, charging pile technology is also constantly developing in the direction

What is Buchholz Relay in Transformer ?Buchholz relay is a gas relay used in oil-immersed transformers to monitor the gas production inside the transformer, so as to detect possible faults inside the transformer.How Buchholz relays workThe Buchholz relay works on the basis of the gas produced when the transformer fails internally. When overheating or discharge failure occurs inside the transformer, gas is produced. These gases will rise and pass through the top of the tank into the oil storage t

What is the Differential Protection of Transformers?Differential Protection DefinitionThe differential protection of transformer is an important relay protection method, which is used to detect the faults inside the transformer, such as winding short circuit, turn short circuit and so on. Differential protection determines whether there is a fault by comparing the difference in current on both sides of the transformer.Principle of differential protectionDifferential protection is based on a basi

What is Over Fluxing in Transformer ?Over Fluxing DefinitionOver fluxing in a transformer occurs when the magnetic flux density exceeds the designed limit, leading to potential damage.Causes of Over FluxingOver fluxing can be caused by overvoltage, low-frequency power generation, lightly loaded transmission lines, and inadequate shunt compensation.Effects of Over Fluxing Over voltage causes due to sudden load rejection Low frequency generation of power Transmission line is lightly loaded Proper

What is Commissioning of Power Transformer ?Transformer Commissioning DefinitionTransformer commissioning is defined as the process of preparing a power transformer for service by conducting various tests and adjusting settings.Buchholz Relay TestBuchholz relay operation for alarm and trip should also be checked by injecting air to the test pocket provided in the relay.Low Oil Level Alarm TestThe low oil level alarm of the magnetic oil gauge should be checked.Temperature Indicator TestThe contac

What is the Maintenance of Transformers ?Maintenance of transformers is essential to ensure their safe, stable and efficient operation, and the following are some common maintenance measures:Periodic inspectionAppearance check: Check whether the transformer shell is damaged, deformed, and leaking oil.Oil temperature check: Use an oil temperature gauge to measure the oil temperature and ensure that it is within the normal range.Oil level check: Observe the oil level in the oil pillow. If the oil

What is Dissolved Gas Analysis (DGA) ?Dissolved Gas Analysis (DGA) DefinitionDissolved gas analysis of transformer oil is a technique to study gases produced under thermal and electrical stress in transformers.Gas Extraction MethodsUsing specialized equipment, gases are extracted and analyzed to diagnose the internal condition of a transformer.Indicative GasesCertain gases like hydrogen, methane, and ethylene signify specific types of thermal stresses based on their amounts and presence.CO and C